N900 Software BME - Revision history

joerg_rw: more

joerg_rw — Fri, 24 Jun 2016 01:54:41 GMT

← Older revision		Revision as of 01:54, 24 June 2016
Line 8:		Line 8:
	* Kernel driver that handles all of the low-level interaction with the hardware. (basically just I2C IO)		* Kernel driver that handles all of the low-level interaction with the hardware. (basically just I2C IO)
	* hald-addon-bme - an add-on process for HAL that reports status.		* hald-addon-bme - an add-on process for HAL that reports status.
-	* bme_RX-51 - Process started early in boot, with ~~watchdogs to reboot~~ the ~~device if it malfunctions~~.	+	* bme_RX-51 - Process started early in boot, with watchdog tickling of the watchdog in chip, configuring the charger chip, selecting charge current etc.

	The kernel driver is split over several files.		The kernel driver is split over several files.

joerg_rw: minor sidenote

joerg_rw — Fri, 24 Jun 2016 01:53:02 GMT

minor sidenote

← Older revision		Revision as of 01:53, 24 June 2016
Line 6:		Line 6:

	BME is divided into three parts.		BME is divided into three parts.
-	* Kernel driver that handles all of the low-level interaction with the hardware.	+	* Kernel driver that handles all of the low-level interaction with the hardware. (basically just I2C IO)
	* hald-addon-bme - an add-on process for HAL that reports status.		* hald-addon-bme - an add-on process for HAL that reports status.
	* bme_RX-51 - Process started early in boot, with watchdogs to reboot the device if it malfunctions.		* bme_RX-51 - Process started early in boot, with watchdogs to reboot the device if it malfunctions.

pali at 09:29, 30 July 2012

pali — Mon, 30 Jul 2012 09:29:18 GMT

← Older revision		Revision as of 09:29, 30 July 2012
Line 29:		Line 29:
	* BME process/file is called <code>/usr/sbin/bme_RX-51</code> and killing or sigstop'ing it will cause immediate or delayed reboot. It is easily suspended though through upstart process management by:<br /><pre>~>stop bme</pre>and resumed any time by:<br /><pre>~>start bme</pre>		* BME process/file is called <code>/usr/sbin/bme_RX-51</code> and killing or sigstop'ing it will cause immediate or delayed reboot. It is easily suspended though through upstart process management by:<br /><pre>~>stop bme</pre>and resumed any time by:<br /><pre>~>start bme</pre>

-	A nice little experiment to investigate the ~~bq24150~~ USB Battery Charger chip's abilities is to	+	A nice little experiment to investigate the bq24150a USB Battery Charger chip's abilities is to
	* plug in Nokia wallwart charger		* plug in Nokia wallwart charger
	* <pre>->stop bme</pre>		* <pre>->stop bme</pre>
-	* wait max 32s until ~~bq24150~~ internal watchdog timer expires (due to bme not resetting it), which will cause ~~bq24150~~ to reset to defaults, which are a mostly sane, safe charging without any software support. You can tell this by ~~bq24150~~ firing up the hardwired steady yellow indicator LED	+	* wait max 32s until bq24150a internal watchdog timer expires (due to bme not resetting it), which will cause bq24150a to reset to defaults, which are a mostly sane, safe charging without any software support. You can tell this by bq24150a firing up the hardwired steady yellow indicator LED

	I'm about to write a first draft little script to somewhat replace bme's basic functions, eventually turning this into a real project Just-Replaces-BME aka jrbme (some say it's "JRBME replaces BME", according to an age old tradition of linux self referencing ETLA [like GNU=="GNU Not Unix", KDE=="KDE Desktop Environment"])		I'm about to write a first draft little script to somewhat replace bme's basic functions, eventually turning this into a real project Just-Replaces-BME aka jrbme (some say it's "JRBME replaces BME", according to an age old tradition of linux self referencing ETLA [like GNU=="GNU Not Unix", KDE=="KDE Desktop Environment"])

amigadave: wikify slightly

amigadave — Fri, 11 Feb 2011 11:04:56 GMT

wikify slightly

← Older revision		Revision as of 11:04, 11 February 2011
Line 9:		Line 9:
	* hald-addon-bme - an add-on process for HAL that reports status.		* hald-addon-bme - an add-on process for HAL that reports status.
	* bme_RX-51 - Process started early in boot, with watchdogs to reboot the device if it malfunctions.		* bme_RX-51 - Process started early in boot, with watchdogs to reboot the device if it malfunctions.
-
-

	The kernel driver is split over several files.		The kernel driver is split over several files.
Line 16:		Line 14:
	http://mxr.maemo.org/fremantle/source/kernel/include/linux/i2c/twl4030-madc.h		http://mxr.maemo.org/fremantle/source/kernel/include/linux/i2c/twl4030-madc.h
	This handles reading various ADCs to readout voltages, currents and BSI.		This handles reading various ADCs to readout voltages, currents and BSI.
-

	'''BSI''', or battery size indicator is the third pin of the battery. Resistance between the - pin and third pin on battery is measured by BME through twl4030-madc, and mapped into a capacity in mAh. BME noticeably uses this as a reference "full" value for the battery meter, and possibly for other uses as well. Here are some experimental results, all resistance readings are to be considered inaccurate at best:		'''BSI''', or battery size indicator is the third pin of the battery. Resistance between the - pin and third pin on battery is measured by BME through twl4030-madc, and mapped into a capacity in mAh. BME noticeably uses this as a reference "full" value for the battery meter, and possibly for other uses as well. Here are some experimental results, all resistance readings are to be considered inaccurate at best:
Line 27:		Line 24:
	Unsorted adds:		Unsorted adds:

-	* Then there's also /usr/lib/hal/hald-addon-bme, which seems not to be completely out of order (according to lshal) even when bme_RX-51 is stopped.	+	* Then there's also <code>/usr/lib/hal/hald-addon-bme</code>, which seems not to be completely out of order (according to lshal) even when bme_RX-51 is stopped.
-		+
	* Mer 'replacement hald-addon-bme': http://gitorious.org/mer-toggles/hald-addon-bme/blobs/master/hald-addon-bme.c [[Mer/Documentation/BME_Protocol]] (N810!)		* Mer 'replacement hald-addon-bme': http://gitorious.org/mer-toggles/hald-addon-bme/blobs/master/hald-addon-bme.c [[Mer/Documentation/BME_Protocol]] (N810!)
-
	* <code>lsof -p `pidof bme_RX-51`</code> gives an idea about what BME is actually interfering/interfacing with, and a strace will show it talks to dsme_lib probably to implement the watchdog timers.		* <code>lsof -p `pidof bme_RX-51`</code> gives an idea about what BME is actually interfering/interfacing with, and a strace will show it talks to dsme_lib probably to implement the watchdog timers.
-
	* BME process/file is called <code>/usr/sbin/bme_RX-51</code> and killing or sigstop'ing it will cause immediate or delayed reboot. It is easily suspended though through upstart process management by:<br /><pre>~>stop bme</pre>and resumed any time by:<br /><pre>~>start bme</pre>		* BME process/file is called <code>/usr/sbin/bme_RX-51</code> and killing or sigstop'ing it will cause immediate or delayed reboot. It is easily suspended though through upstart process management by:<br /><pre>~>stop bme</pre>and resumed any time by:<br /><pre>~>start bme</pre>

Line 47:		Line 41:
	Editing this without understanding can CAUSE YOUR N900 TO CATCH FIRE.		Editing this without understanding can CAUSE YOUR N900 TO CATCH FIRE.

-	=Replacement Goals=	+	==Replacement Goals==
-	==Alpha==	+	===Alpha===
	* Not make the battery explode.		* Not make the battery explode.
	* Charge from any 5V source, assuming the battery is in a safe condition, just setting the charger chip to the end voltage, and resetting the watchdog.		* Charge from any 5V source, assuming the battery is in a safe condition, just setting the charger chip to the end voltage, and resetting the watchdog.
-	==Beta==	+	===Beta===
	* Watch the state of the battery, and charge taking into account device load.		* Watch the state of the battery, and charge taking into account device load.
	** Battery charger chip should be configured to float the battery at a current which slightly exceeds the desired float current, and the charge normally terminated when the actual battery current measured by the bq27200 reaches the 'taper' value. A simple way to measure this is if the 'time till full' field goes to 65535. This ensures a consistent shutoff taper current, which the battery charger alone cannot do.		** Battery charger chip should be configured to float the battery at a current which slightly exceeds the desired float current, and the charge normally terminated when the actual battery current measured by the bq27200 reaches the 'taper' value. A simple way to measure this is if the 'time till full' field goes to 65535. This ensures a consistent shutoff taper current, which the battery charger alone cannot do.

-	==Gamma==	+	===Gamma===
	* Charge at appropriate limits for USB chargers, and USB hosts we are plugged into.		* Charge at appropriate limits for USB chargers, and USB hosts we are plugged into.
	* Monitor and reset from abnormal conditions - incorrect 'battery missing' and other error codes. Capacity and charge data from bq27200 can be very inaccurate if the phone has not appropriately learned the capacity of the battery, or if it erroneously detects battery full due to a high impedence battery or poor contact.		* Monitor and reset from abnormal conditions - incorrect 'battery missing' and other error codes. Capacity and charge data from bq27200 can be very inaccurate if the phone has not appropriately learned the capacity of the battery, or if it erroneously detects battery full due to a high impedence battery or poor contact.
		+	* If phone is in active use, and charger or USB is plugged in, maintain a constant battery voltage somewhat under the peak charge voltage, without regards to taper current. (To keep phone charged, but not degrade battery with pointless micro-cycling, or high float voltage)

-	* If phone is in active use, and charger or USB is plugged in, maintain a constant battery voltage somewhat under the peak charge voltage, without regards to taper current. (To keep phone charged, but not degrade battery with pointless micro-cycling, or high float voltage	+	[[Category:N900_Hardware]]
-	)	+
-	[[~~category~~:N900_Hardware]]	+

85.17.200.76: Add BSI and BSI-resistance to mAh mapping

85.17.200.76 — Sun, 01 Aug 2010 16:57:12 GMT

Add BSI and BSI-resistance to mAh mapping

← Older revision		Revision as of 16:57, 1 August 2010
Line 15:		Line 15:

	http://mxr.maemo.org/fremantle/source/kernel/include/linux/i2c/twl4030-madc.h		http://mxr.maemo.org/fremantle/source/kernel/include/linux/i2c/twl4030-madc.h
-	This handles reading various ADCs to readout voltages ~~and~~ currents.	+	This handles reading various ADCs to readout voltages, currents and BSI.

		+
		+	'''BSI''', or battery size indicator is the third pin of the battery. Resistance between the - pin and third pin on battery is measured by BME through twl4030-madc, and mapped into a capacity in mAh. BME noticeably uses this as a reference "full" value for the battery meter, and possibly for other uses as well. Here are some experimental results, all resistance readings are to be considered inaccurate at best:
		+
		+	100 kΩ 1250mAh (Original BL-5J battery)
		+	90 kΩ 1000mAh
		+	80 kΩ 862mAh
		+	78 kΩ 740mAh

	Unsorted adds:		Unsorted adds:

speedevil at 10:31, 4 June 2010

speedevil — Fri, 04 Jun 2010 10:31:12 GMT

← Older revision		Revision as of 10:31, 4 June 2010
Line 2:		Line 2:

	This is required to implement user friendly [[N900_Hardware_USB_Host\|Host Mode]]		This is required to implement user friendly [[N900_Hardware_USB_Host\|Host Mode]]
		+
		+	See also the garage project [https://garage.maemo.org/projects/jrbme/ JR-BME].

	BME is divided into three parts.		BME is divided into three parts.

speedevil: /* Gamma */

speedevil — Fri, 21 May 2010 00:29:32 GMT

Gamma

← Older revision		Revision as of 00:29, 21 May 2010
Line 48:		Line 48:
	==Gamma==		==Gamma==
	* Charge at appropriate limits for USB chargers, and USB hosts we are plugged into.		* Charge at appropriate limits for USB chargers, and USB hosts we are plugged into.
-	* Monitor and reset from abnormal conditions - incorrect 'battery missing' and other error codes.	+	* Monitor and reset from abnormal conditions - incorrect 'battery missing' and other error codes. Capacity and charge data from bq27200 can be very inaccurate if the phone has not appropriately learned the capacity of the battery, or if it erroneously detects battery full due to a high impedence battery or poor contact.
		+
	* If phone is in active use, and charger or USB is plugged in, maintain a constant battery voltage somewhat under the peak charge voltage, without regards to taper current. (To keep phone charged, but not degrade battery with pointless micro-cycling, or high float voltage		* If phone is in active use, and charger or USB is plugged in, maintain a constant battery voltage somewhat under the peak charge voltage, without regards to taper current. (To keep phone charged, but not degrade battery with pointless micro-cycling, or high float voltage
	)		)
	[[category:N900_Hardware]]		[[category:N900_Hardware]]

speedevil: /* Gamma */

speedevil — Tue, 18 May 2010 09:30:36 GMT

Gamma

← Older revision		Revision as of 09:30, 18 May 2010
Line 48:		Line 48:
	==Gamma==		==Gamma==
	* Charge at appropriate limits for USB chargers, and USB hosts we are plugged into.		* Charge at appropriate limits for USB chargers, and USB hosts we are plugged into.
-		+	* Monitor and reset from abnormal conditions - incorrect 'battery missing' and other error codes.
		+	* If phone is in active use, and charger or USB is plugged in, maintain a constant battery voltage somewhat under the peak charge voltage, without regards to taper current. (To keep phone charged, but not degrade battery with pointless micro-cycling, or high float voltage
		+	)
	[[category:N900_Hardware]]		[[category:N900_Hardware]]

speedevil: /* Beta */

speedevil — Sun, 16 May 2010 21:04:38 GMT

Beta

← Older revision		Revision as of 21:04, 16 May 2010
Line 44:		Line 44:
	==Beta==		==Beta==
	* Watch the state of the battery, and charge taking into account device load.		* Watch the state of the battery, and charge taking into account device load.
		+	** Battery charger chip should be configured to float the battery at a current which slightly exceeds the desired float current, and the charge normally terminated when the actual battery current measured by the bq27200 reaches the 'taper' value. A simple way to measure this is if the 'time till full' field goes to 65535. This ensures a consistent shutoff taper current, which the battery charger alone cannot do.
		+
	==Gamma==		==Gamma==
	* Charge at appropriate limits for USB chargers, and USB hosts we are plugged into.		* Charge at appropriate limits for USB chargers, and USB hosts we are plugged into.

	[[category:N900_Hardware]]		[[category:N900_Hardware]]

speedevil at 14:49, 14 May 2010

speedevil — Fri, 14 May 2010 14:49:08 GMT

← Older revision		Revision as of 14:49, 14 May 2010
Line 32:		Line 32:

	I'm about to write a first draft little script to somewhat replace bme's basic functions, eventually turning this into a real project Just-Replaces-BME aka jrbme (some say it's "JRBME replaces BME", according to an age old tradition of linux self referencing ETLA [like GNU=="GNU Not Unix", KDE=="KDE Desktop Environment"])		I'm about to write a first draft little script to somewhat replace bme's basic functions, eventually turning this into a real project Just-Replaces-BME aka jrbme (some say it's "JRBME replaces BME", according to an age old tradition of linux self referencing ETLA [like GNU=="GNU Not Unix", KDE=="KDE Desktop Environment"])
		+
		+	Joerg's script can be found [http://talk.maemo.org/showpost.php?p=658278&postcount=861 here].
		+	It should not be used by anyone who has not read and understood all relevant datasheets, and understands why it does what it does.
		+
		+	Editing this without understanding can CAUSE YOUR N900 TO CATCH FIRE.

	=Replacement Goals=		=Replacement Goals=